# elisp.texi specially defines \tocreadfilename when VOL1 or VOL2 is
# set, so we can use our premade .toc's.
-#
+#
vol1.pdf: elisp1med-fns-ready elisp1med-aux-ready elisp1med-toc-ready
- @echo -e "\f Final TeX run for volume 1..."
+ @printf '\f Final TeX run for volume 1...\n'
cp elisp1med-toc-ready elisp1-toc-ready.toc
cp elisp1med-fns-ready vol1.fns
cp elisp1med-aux-ready vol1.aux
$(tex2)
# \f intermediate toc files.
-#
+#
# vol1 toc: volume 1, page break, volume 2 (with II: prepended).
elisp1med-toc-ready: elisp1med-init elisp2med-init
echo '@unnchapentry{@b{Volume 1}}{10001}{vol1}{}' >$@
cat elisp1med-toc >>$@
echo '@page' >>$@
echo '@unnchapentry{@b{Volume 2}}{10001}{vol2}{}' >>$@
- sed 's/{\([^}]*\)}$$/{II:\1}/' elisp2med-toc >>$@
+ sed 's/{\([^}]*\)}$$/{II:\1}/' elisp2med-toc >>$@
#
# vol2 toc: volume 1 (with I: prepended), page break, volume 2.
elisp2med-toc-ready: elisp1med-init elisp2med-init
echo '@unnchapentry{@b{Volume 1}}{10001}{vol1}{}' >$@
- sed 's/{\([^}]*\)}$$/{I:\1}/' elisp1med-toc >>$@
+ sed 's/{\([^}]*\)}$$/{I:\1}/' elisp1med-toc >>$@
echo '@page' >>$@
echo '@unnchapentry{@b{Volume 2}}{10001}{vol2}{}' >>$@
cat elisp2med-toc >>$@
# \f intermediate aux files.
-#
-# append vol2's fixed aux to normal vol1.
+#
+# append vol2's fixed aux to normal vol1.
elisp1med-aux-ready: elisp2med-aux-vol-added
cat elisp1med-aux $< >$@
#
sed 's/-pg}{\(.*\)}$$/-pg}{\1, vol.@tie2}/' elisp2med-aux >$@
# \f intermediate index (fns) file.
-#
+#
elisp1med-fns-ready: elisp1med-fn-vol-added elisp2med-fn-vol-added
cat elisp2med-fn-vol-added >>vol1.fn
texindex vol1.fn
# -----------------------------------------------------------------------------
# \f intermediate TeX runs.
-#
+#
# this generates what would be the final versions -- except the page
# numbers aren't right. The process of adding the I: and II: changes
# the page breaks, so a few index entries, at least are wrong. (In
# 2007, x-meta-keysym in vol.II ended up on page 374 when the index had
# it on page 375 from the initial run.)
-#
+#
# So, we start all over again, from these fns/aux/toc files.
-#
+#
elisp1med-init: elisp1-fns-ready elisp1-aux-ready elisp1init-toc-ready $(texinfodir)/texinfo.tex
- @echo -e "\f Intermediate TeX run for volume 1..."
+ @printf '\f Intermediate TeX run for volume 1...\n'
cp elisp1init-toc-ready elisp1-toc-ready.toc
cp elisp1-fns-ready vol1.fns
cp elisp1-aux-ready vol1.aux
# \f initial toc files.
-#
+#
# vol1 toc: volume 1, page break, volume 2 (with II: prepended).
elisp1init-toc-ready: elisp1-init elisp2-init
echo '@unnchapentry{@b{Volume 1}}{10001}{vol1}{}' >$@
cat elisp1-toc >>$@
echo '@page' >>$@
echo '@unnchapentry{@b{Volume 2}}{10001}{vol2}{}' >>$@
- sed 's/{\([^}]*\)}$$/{II:\1}/' elisp2-toc >>$@
+ sed 's/{\([^}]*\)}$$/{II:\1}/' elisp2-toc >>$@
#
# vol2 toc: volume 1 (with I: prepended), page break, volume 2.
elisp2init-toc-ready: elisp1-init elisp2-init
echo '@unnchapentry{@b{Volume 1}}{10001}{vol1}{}' >$@
- sed 's/{\([^}]*\)}$$/{I:\1}/' elisp1-toc >>$@
+ sed 's/{\([^}]*\)}$$/{I:\1}/' elisp1-toc >>$@
echo '@page' >>$@
echo '@unnchapentry{@b{Volume 2}}{10001}{vol2}{}' >>$@
cat elisp2-toc >>$@
# \f initial aux files.
-#
+#
# append vol2's fixed aux to normal vol1. The initial runs saved
# elisp1-aux and elisp2-aux.
elisp1-aux-ready: elisp2-aux-vol-added
sed 's/-pg}{\(.*\)}$$/-pg}{\1, vol.@tie2}/' elisp2-aux >$@
# \f initial index (fns) file.
-#
+#
# Append other volume's index entries to this one's.
# Index entries in this volume will then take precedence.
elisp1-fns-ready: elisp1-fn-vol-added elisp2-fn-vol-added
# \f initial TeX runs.
-#
+#
# We use the .fn, .aux, and .toc files created here in subsequent
# processing. The page numbers generated here will not be correct yet,
# but we run texindex and TeX a second time just to get them closer.
# Otherwise it might take even longer for them to converge.
-#
+#
elisp1-init: elisp.texi
- @echo -e "\f Initial TeX run for volume 1..."
+ @printf '\f Initial TeX run for volume 1...\n'
rm -f vol1.aux vol1.toc
$(tex1)
texindex vol1.??
touch $@
# COPYING CONDITIONS
-#
+#
# This file is free software: you can redistribute it and/or modify
# it under the terms of the GNU General Public License as published by
# the Free Software Foundation, either version 3 of the License, or
# (at your option) any later version.
-#
+#
# This file is distributed in the hope that it will be useful,
# but WITHOUT ANY WARRANTY; without even the implied warranty of
# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
# GNU General Public License for more details.
-#
+#
# You should have received a copy of the GNU General Public License
# along with this file. If not, see <http://www.gnu.org/licenses/>.
-